Common Control and Measurement Plane R. Rokui
Internet-Draft Ciena
Intended status: Informational A. Guo
Expires: 22 April 2025 Futurewei Technologies
P. Bedard
Cisco
B. Swamynathan
Nokia
G. Grammel
Juniper
19 October 2024
Data Modelling and Gap Analysis of Optical Pluggables in Packet Over
Optical Network
draft-rokui-ccamp-actn-wdm-pluggable-modelling-01
Abstract
This draft outlines the modeling of optical pluggables within a host
packet device in the context of a packet over optical network. The
model encompasses all pertinent properties of the pluggable for
various packet over optical use cases and is partitioned into three
primary areas: the optical media side, the electrical plug to host
interconnect, and the physical equipment of the pluggable.
Included in the model are representations of configuration, states,
and telemetry data, as well as of profiles and coherent plug
capabilities. Emphasizing the importance of considering both vendor-
agnostic and vendor-specific attributes in modeling coherent
pluggables.
Drawing from existing IETF models and potentially complementing that
with input from other standard or industrial forum models (ITU-T,
OpenConfig , ONF TAPI etc.) , this model offers enhanced uniform
structuring and naming.
This draft introduces the concept of "Coherent Pluggable Manifest",
where it represents the capabilities of pluggable, maintained in a
repository. This document also covers gap analysis of current IETF
drafts and other SDOs on coherent Pluggable attributes and provides
the complete lifecycle of a coherent pluggable from operators'
approval through viability assessment to deployment.
Rokui, et al. Expires 22 April 2025 [Page 1]
Internet-Draft Modelling Optical Pluggables October 2024
This document also covers an analysis of the gap between current IETF
drafts and the corresponding works in other standards bodies and
industry. The lifecycle of a coherent pluggable from operators'
approval, viability assessment to deployment and monitoring is also
covered.
About This Document
This note is to be removed before publishing as an RFC.
The latest revision of this draft can be found at
https://italobusi.github.io/actn-wdm-pluggable-modelling/draft-rokui-
ccamp-actn-wdm-pluggable-modelling.html. Status information for this
document may be found at https://datatracker.ietf.org/doc/draft-
rokui-ccamp-actn-wdm-pluggable-modelling/.
Discussion of this document takes place on the Common Control and
Measurement Plane Working Group mailing list (mailto:ccamp@ietf.org),
which is archived at https://mailarchive.ietf.org/arch/browse/ccamp/.
Subscribe at https://www.ietf.org/mailman/listinfo/ccamp/.
Source for this draft and an issue tracker can be found at
https://github.com/italobusi/actn-wdm-pluggable-modelling.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at https://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on 22 April 2025.
Copyright Notice
Copyright (c) 2024 IETF Trust and the persons identified as the
document authors. All rights reserved.
Rokui, et al. Expires 22 April 2025 [Page 2]
Internet-Draft Modelling Optical Pluggables October 2024
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents (https://trustee.ietf.org/
license-info) in effect on the date of publication of this document.
Please review these documents carefully, as they describe your rights
and restrictions with respect to this document. Code Components
extracted from this document must include Revised BSD License text as
described in Section 4.e of the Trust Legal Provisions and are
provided without warranty as described in the Revised BSD License.
Table of Contents
1. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 4
2. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 5
3. Optical Pluggable in a Device with Packet Functions . . . . . 7
4. Coherent Pluggable Functional Building Blocks . . . . . . . . 9
4.1. Optical Channel/OTSI . . . . . . . . . . . . . . . . . . 10
4.2. Media Logical Channels . . . . . . . . . . . . . . . . . 10
4.3. Host Logical Channels . . . . . . . . . . . . . . . . . . 10
4.4. Electrical Channels . . . . . . . . . . . . . . . . . . . 11
4.5. Equipment . . . . . . . . . . . . . . . . . . . . . . . . 11
5. Optical Pluggables Data Modeling . . . . . . . . . . . . . . 12
5.1. Coherent Pluggable Capability Attributes (aka,
Supported-Modes) . . . . . . . . . . . . . . . . . . . . 12
5.2. Coherent Pluggable Configurations Attributes . . . . . . 14
5.3. Coherent Pluggable Performance Monitoring Data . . . . . 15
5.4. Coherent Pluggable Threshold Definition . . . . . . . . . 17
5.5. Coherent Pluggable Alarm Notifications . . . . . . . . . 18
5.6. Support of Vendor-Specific Attributes . . . . . . . . . . 18
5.6.1. Vendor-Specific Capability Attributes . . . . . . . . 19
5.6.2. Vendor-Specific Configuration Attributes
(Solution-1) . . . . . . . . . . . . . . . . . . . . 20
5.6.3. Vendor-Specific Configuration Attributes
(Solution-2) . . . . . . . . . . . . . . . . . . . . 21
5.6.4. Vendor-Specific Configuration Attributes
(Solution-3) . . . . . . . . . . . . . . . . . . . . 22
5.6.5. Vendor-Specific Secret Capability Attributes . . . . 23
5.6.6. Vendor-Specific Secret Configuration Attributes . . . 23
5.6.7. Support of Vendor-Specific Performance Monitoring
Data . . . . . . . . . . . . . . . . . . . . . . . . 24
6. Coherent Pluggables Yang Data Model . . . . . . . . . . . . . 24
7. Coherent Pluggable Data Modeling Gap Analysis . . . . . . . . 26
8. Coherent Pluggable Manifest . . . . . . . . . . . . . . . . . 27
9. Optical Pluggables Lifecycle Management . . . . . . . . . . . 33
9.1. Approving the pluggable type and version . . . . . . . . 34
9.2. Planning the network . . . . . . . . . . . . . . . . . . 35
9.3. Dealing with service demand . . . . . . . . . . . . . . . 36
9.4. Installing and operationalising the pluggable . . . . . . 37
9.5. Expressing capabilities . . . . . . . . . . . . . . . . . 38
Rokui, et al. Expires 22 April 2025 [Page 3]
Internet-Draft Modelling Optical Pluggables October 2024
10. Implications for the Functional Control Architecture . . . . 39
11. Usage of Coherent Pluggables Manifest . . . . . . . . . . . . 39
11.1. Example-1: Coherent Pluggables Manifest . . . . . . . . 40
11.2. Example-2: Coherent Pluggables Manifest . . . . . . . . 42
12. Security Considerations . . . . . . . . . . . . . . . . . . . 45
13. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 45
14. References . . . . . . . . . . . . . . . . . . . . . . . . . 45
14.1. Normative References . . . . . . . . . . . . . . . . . . 45
14.2. Informative References . . . . . . . . . . . . . . . . . 46
Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . . . 47
Contributors . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 48
1. Terminology
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
"OPTIONAL" in this document are to be interpreted as described in
BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all
capitals, as shown here.
The following terms abbreviations are used in this document:
* Optical Pluggable / Coherent Pluggable / Pluggable: A small form
factor coherent optical module. This document uses these terms
interchangeably
* O-PNC: The control functions specializing in management/control of
optical and photonic functions (virtual or physical). See
[RFC8453]
* P-PNC: The control functions specializing in management/control of
packet functions (virtual or physical). See [RFC8453]
* CMIS: The Common Management Interface Specification is an OIF
Implementation Agreement (IA) which provides a well-defined
mechanism to initialize and manage optical (and copper) modules in
a standard way, while still providing the capability to provide
custom functionality. This commonality makes integration into
different host platforms easier for both the host and module
vendors.
* optical pluggable media side:
* optical pluggable host side:
Rokui, et al. Expires 22 April 2025 [Page 4]
Internet-Draft Modelling Optical Pluggables October 2024
* Monitored attributes: The Coherent Pluggable attributes which can
be measured, monitored, estimated, or otherwise observed. The
monitored attributes are the inputs to performance monitors which
in turn provide real time samples, threshold crossing supervision,
and sometimes sample statistics.
2. Introduction
Packet traffic has been transmitted across optical networks for many
years, leveraging the advantages of optical transmission and
switching combined with packet switching. Traditionally, optical
systems and packet systems have been distinct, each with their own
dedicated devices.
In numerous network setups, packet and optical networks have been
engineered, operated, and managed separately, leading to siloed
operations that can be suboptimal and inefficient. The evolution of
both packet and optical systems has largely been independent.
Optical systems, in particular, have seen advancements in capacity,
especially with the adoption of coherent optical techniques.
Advancements in optical component design have led to increased
density, enabling entire coherent optical terminal systems that
previously required multiple circuit packs to now fit into a single
small form factor "coherent pluggable." Integrating coherent
pluggables into devices with packet functions can result in reduced
network costs, power consumption, and footprint, while also enhancing
data transfer rates, reducing latency, and expanding capacity,
although in some cases, separate packet and optical solutions may
still be preferred due to other engineering and deployment
considerations.
These trends, coupled with the desire to utilize the best components
available, have given rise to open optical pluggables. These
pluggables allow a plug from one vendor to be installed in a device
from another vendor with packet functions. Communication between
coherent pluggables and the packet device host occurs through the
CMIS standard developed by OIF [OIF-CMIS].
While standardized transmission modes like ZR can handle basic
applications, proprietary modes from vendors are often necessary to
achieve optimal performance.
This draft outlines the modeling of an optical pluggable within a
host packet device in context of a packet over optical network. The
model presented in this document consolidates various properties of
optical pluggables into three key functional block:
Rokui, et al. Expires 22 April 2025 [Page 5]
Internet-Draft Modelling Optical Pluggables October 2024
* Photonic/Optical attributes: These attributes defines the
characteristics of the optical and photonic properties such as
spectrum, polarization, dispersion etc., which do not directly
affect the behavior of the host packet device.
* Host/Electrical attributes: These attributes defines the
characteristics of interconnect between the host and the optical
pluggable, such as lane count, FEC etc., which both the optical
pluggable and the packet host must understand and act upon.
* Physical and functional aspects of the pluggable (i.e.,
equipment): This defines attributes of the optical pluggable
itself, such as plug type, version, thermal characteristics, power
consumption etc., which indirectly affect the packet host.
For each of these functional blocks, coherent pluggable model
provides attributes in following areas:
* Capabilities: These attributes are read-only and defines the
functional capabilities of the optical pluggables. They are
defined in a profile called "operational-mode" and contains
attributes such as modulation, bit-rate, baud-rate, chromatic-
dispersion, polarization, FEC etc. Generally an optical pluggable
might support multiple operational-modes.
* Configurations: Since an optical pluggable can support multiple
operational-modes, these read-write attributes configure the
pluggables to be functional in one of those operational- modes.
Example of configuration attributes are output power, central
frequency and operational-mode.
* States and performance monitoring telemetry data: These read-only
attributes will be generated by optical pluggables and represents
various states and PM data of the optical pluggable such as
channel input power, channel output power, central frequency,
laser temperature, current OSNR, Link Up/Down State, Alarm State,
Laser On/Off State etc. In most cases these attributes are
changing with time and pluggable reports current, average, min and
max values. It is also possible to apply thresholds on each of
these attributes to support thershold crossing alert (TCA).
Both vendor-agnostic and vendor-specific attributes are important
considerations in the modeling of coherent pluggables.
The document is divided into the following sections:
* Section 3: Optical Pluggable in a Device with Packet Functions
Rokui, et al. Expires 22 April 2025 [Page 6]
Internet-Draft Modelling Optical Pluggables October 2024
* Section 4: Coherent Pluggables Building Blocks
* Section 5: Coherent Pluggables Data Modeling
* Section 6: Coherent Pluggables Yang Model
* Section 7: Coherent pluggable Gap Analysis
* Section 8: Coherent Pluggables Manifest
* Section 9: Optical Pluggables Lifecycle Management
* Section 10: Functional Architecture Implications
* Section 11: Usage of Coherent Pluggables Manifest
3. Optical Pluggable in a Device with Packet Functions
Figure 1 shows a host packet device from vendor X, which is connected
to optical device, equipped with optical pluggables from vendor X and
Y. This figure exposes the following internal and external
interfaces:
A. This interface provides the control of host packet functions and
optical functions. It provides these functions which can be
decoupled such that there is no overlap between the optical and
packet control functions.
B. The CMIS communication interface between host packet devices) and
optical pluggables.
C. The data flow between the coherent pluggable and the packet data
function through this interface. This is electrical interface
between coherent pluggable and the host. Section 4 will discuss this
in more details.
D. Optical fiber connecting the optical devices to optical
pluggables. This carries the flow of photonic signal from the
optical device to the coherent pluggables. Section 4 will discuss
this in more details.
This draft presents the modeling of the coherent pluggable such as
(D) and (C) in Figure 1 within a host packet device. The model
presented in Section 5 consolidates properties of coherent pluggable
on interfaces (D) and (C) where interface (D) provides the photonic/
optical attributes and interface (C) provides the host/electrical
attributes.
Rokui, et al. Expires 22 April 2025 [Page 7]
Internet-Draft Modelling Optical Pluggables October 2024
|---------------|
| P-PNC(s), |
| O-PNC(s), |
| MDSC |
|---------------|
^
| (A)
+-------------------|-------------------+
| |---------------| |
| |Host Management| |
| |---------------| |
| | | Packet Device
| V | Vendor X
| |---------------------| | (i.e, Host)
| v v |
| |-----------| |----------| |
| | Packet | | Coherent | |
| | Function |..........| Plug | |
| | Data | | Data | |
| |-----------| |----------| |
| . . |
| . . (B) |
| . . |
| |--------------| (C) |------------------| (D)
| |Packet Device |<------->| Coherent Plug #1 |=======
| |Function |<---| | Vendor X |
| |--------------| | |------------------|
| | |
| | |------------------|
| |--->| Coherent Plug #2 |=======
| | Vendor Y |
| |------------------|
| |
+---------------------------------------+
Legend
(A) Packet device management interfaces
(e.g., YANG, NETCONF, gNMI, etc.)
(B) CMIS interface between Optical pluggable and Host
(C) Host side of coherent pluggable (towards the Host)
(D) Media side of coherent pluggable
(towards Optical/Photonic network)
Figure 1: Packet device with optical pluggables
Rokui, et al. Expires 22 April 2025 [Page 8]
Internet-Draft Modelling Optical Pluggables October 2024
4. Coherent Pluggable Functional Building Blocks
The functional building blocks of the coherent pluggables of Figure 1
are shown in Figure 2 and has three major functions:
* Media side: This functional block represents all Photonic/Optical
attributes of the coherent pluggables (interface (5) in Figure 1).
These attributes define the characteristics of the optical and
photonic properties such as spectrum, polarization, dispersion
etc., which do not directly affect the behavior of the host packet
device. Note that the goal of this draft is to eventually provide
the YANG data model with these specific paramters which can be
exposed in the model towards the controllers.
* Host side: This functional block represents all Host/Electrical
attributes of the coherent pluggables (interface (4) in Figure 1).
These attributes defines the characteristics of interconnect
between the host and the optical pluggable, such as lane count,
FEC etc., which both the optical pluggable and the packet host
should understand and act upon.
* Equipment attributes: These attributes represent all physical and
functional aspects of the coherent pluggable such as plug type,
software version, thermal characteristics, power consumption etc.
Coherent Pluggable
|--------------------------------------------------------------|
| |
| |--------------------------------------------------------| |
| | Equipment | |
| |--------------------------------------------------------| |
| |
| Host side Media side |
| |---------------------------| |---------------------------| |
| | | | | |
| | |---------| |---------| | | |---------| |---------| | |(Tx)
-----| Elec. | | Host | | | | Media | | Optical | ----->
-----| Channels|--| Logical |-------| Logical |--| Channel | <-----
-----| | | Channels| | | | Channels| | (OTSI) | | |(Rx)
| | |---------| |---------| | | |---------| |---------| | |
| | | | | |
| |---------------------------| |---------------------------| |
| |
|--------------------------------------------------------------|
Figure 2: Optical Pluggable Building Blocks
Rokui, et al. Expires 22 April 2025 [Page 9]
Internet-Draft Modelling Optical Pluggables October 2024
The following sections are describing the details of coherent
pluggable functional blocks in more details.
4.1. Optical Channel/OTSI
The media side of the coherent pluggable is further divided into two
functional blocks; Optical Channel/OTSI and Media Logical Channels.
The characterises of the Optical channel/OTSI are:
* This is the pluggable interfaces facing the optical network.
* Represents the digital wrapper that transports services over a
wavelength
* Represents the wavelength and the coherent aspects of the signal
modulated onto it baud-rate, bit-rate, modulation scheme,
frequency, tx-power, etc.
* Optical signal FEC termination/source, FEC characteristic
information – configuration, if possible, Pre-FEC BER, Post-FEC
BER, fail/degrade thresholds, raw corrected/uncorrected counts
* Provides configuration of the signal and monitoring capabilities
* Provides monitoring capabilities in the Tx (toward fiber/medium)
and Rx (from fiber/medium) directions, Total optical power,
optical channel power, Coherent statistics
4.2. Media Logical Channels
The characteristics of the Media Logical Channels are:
* Logical representation of the hierarchical view of the digital
framing layers used for transport of services over the wavelength
* Provides access to information for configuration and monitoring
characteristics. For example, for 400ZR/OpenZR+, it represents
the 400ZR frame structure in which Ethernet services are mapped
and for an OTN encapsulated signal, it represents the OTU, ODU,
OPU frame structures, perhaps with a multi-layer multiplex
structure, in which Ethernet and other types of services are
mapped
4.3. Host Logical Channels
The host side of the coherent pluggable is further divided into two
functional blocks; Host Logical Channels and Electrical channels.
The characteristics of the Host Logical Channels are:
Rokui, et al. Expires 22 April 2025 [Page 10]
Internet-Draft Modelling Optical Pluggables October 2024
* Logical representation of the hierarchical view of the digital
framing layers for services carried on the electrical lanes of the
device
* Provides information for configuration and monitoring
characteristics of each service
* Represents each service carried over the media logical channel and
optical interface/wavelength, e.g., 25GE, 50GE, 100GE, 200GE,
400GE, OTU4, OTUCn etc.
4.4. Electrical Channels
The characteristics of the Electrical Channels are:
Note that the purpose of this section is to clarify the role of
electrical channel in the coherent pluggable. This purpose of this
draft is not to define the data model of the electrical channels.
* The host side lanes of the device forming the physical interface
to the host platform data path device(s)
* Lanes grouped to support the type/format and bandwidth of the
signal used for a service
* Provides information for configuration and monitoring
characteristics of the signal for a service in the electrical
domain, e.g., Interface-format, FEC, alarming thresholds, etc.
* Provides monitoring capabilities in the Tx (toward fiber) and Rx
(from the fiber).
4.5. Equipment
The "Equipment functional block" in Figure 2 represents the coherent
pluggable itself and has the following characteristics:
* Provides manufacturer identification information for the device
* Advertises capabilities of the device including capabilities for
the host/client side and the media/line side
* Provides monitoring capabilities of physical characteristics and
health of the device, e.g., temperature, voltage, coherent
transmitter/receiver characteristics
* Provides for configuration where applicable – e.g., of device
environmental thresholds
Rokui, et al. Expires 22 April 2025 [Page 11]
Internet-Draft Modelling Optical Pluggables October 2024
* Supports device level capabilities such as firmware installation,
restarts, etc.
5. Optical Pluggables Data Modeling
The attributes of all functional building block of a coherent
pluggable in Figure 2 will be exposed to external packet and optical
controllers via host interface (1) shown in Figure 1. To this end,
we need to model the coherent pluggable building blocks described in
Section 4.
The data modeling of each functional blocks provides attributes in
following areas:
* Section 5.1: Coherent pluggable capability attributes (i.e.,
supported-modes)
* Section 5.2: Coherent pluggable configuration attributes
* Section 5.3: Coherent pluggable performance monitoring data
(including State data)
* Section 5.4: Coherent pluggable threshold definition
* Section 5.5: Coherent pluggable alarm notifications
* Section 5.6: Support of Vendor-Specific Attributes
5.1. Coherent Pluggable Capability Attributes (aka, Supported-Modes)
Coherent pluggable have revolutionized optical networking by offering
a powerful combination of high performance, flexibility, and ease of
deployment. These modules support a broad range of capabilities,
making them both efficient and versatile. Their extensive functional
capabilities further enhance their effectiveness in diverse
networking environments.
From a coherent pluggable data modeling perspective, a set of
attributes is grouped together and represented by a single identifier
known as the "Supported Mode." In essence, each supported mode
encapsulates a combination of functional capabilities for coherent
pluggables, such as modulation type, bit rate, baud rate, chromatic
dispersion, polarization, FEC, and more. Some of these attributes
may also include value ranges (e.g., minimum and maximum). A
coherent pluggable can support multiple supported modes, each of
which can be defined by one of the following methods:
Rokui, et al. Expires 22 April 2025 [Page 12]
Internet-Draft Modelling Optical Pluggables October 2024
* Method 1: Defined by a Standards Developing Organization (SDO)
such as ITU-T
* Method 2: Defined by a forum such as Optical Internetworking Forum
(OIF), a group of operators (OpenConfig) or by an individual
vendor
These methods define a namespace for the authority that specified the
particular supported mode, whether it be a standards body, an
association, a group of operators, or an individual vendor. For
example, the supported modes in method 1 are well-known capabilities
established by standards bodies such as the ITU-T [G.698.2]. These
modes are recognized and supported by coherent pluggables, routers,
and SDN controllers. This draft also supports the work of other
Standards Development Organizations (SDOs), forums, or individual
vendors as their specifications become available. In contrast, the
supported-modes in method 2 are capabilities specified by forums such
as OIF [OIF-400ZR], OpenConfig, or by individual vendors. These
supported-modes might not be supported by all coherent-pluggables,
routers or SDN controllers. In specific, the supported-modes defined
by an individual vendor might be not be recognized and supported by
any routers and SDN controllers.
It is important to note that, from a functional perspective of
coherent pluggables, the authority that defined the supported modes
is less critical than the specific attributes associated with each
supported mode. The key consideration is the list of attributes
defined by these supported modes.
As illustrated in Figure 3, this document utilizes a consistent data
structure for defining supported modes, irrespective of the authority
that specified them. It includes:
* supported-mode-id: Identification of the supported mode
* organization-id: This provides a name space for an authority who
defines the supported-mode, i.e., the authority that defines the
supported-mode, such as ITU-T, OIF, OpenConfig, or a vendor
* tags: Optional multiple tags that can be used for various
purposes, mainly for future extensibility. For example, these
tags can map the supported-mode to CMIS Media-ID (if they are not
the same). Other potential uses of this tag are reserved for
future developments.
* operational-mode: This is the main part of this document which
contains a list of capability attributes supported by the coherent
pluggable.
Rokui, et al. Expires 22 April 2025 [Page 13]
Internet-Draft Modelling Optical Pluggables October 2024
Section 8 discusses the concept of the "coherent pluggable manifest",
which is a repository for all supported-modes". It also outlines the
benefit of such repository and various use-cases. Some details of
supported modes can be found in IETF draft [Impairment].
|-----------------------------------------------------------------|
| supported-mode* // list of supported-modes |
| supported-mode-id |
| organization-id (e.g., ITU-T, OIF, OpenConfig or Vendor) |
| tag* // Optional. It has various usage in future |
| operational-mode |
| capability-attribute-1 |
| capability-attribute-2 |
| .... |
| capability-attribute-n |
|-----------------------------------------------------------------|
Figure 3: Data structure for Coherent pluggable supported-modes
As an example, the operational-mode 0x3E introduced by OIF contains
the following read-only capability attributes. Notes that in general
a coherent pluggable can support multiple operational modes.
organization-id: OIF
operational-mode: 0x3E
modulation: DP-16QAM
bit-rate: 478.75 Gbps
baud-rate: 59.84375 Gbd
more attributes ...
5.2. Coherent Pluggable Configurations Attributes
Referring to Figure 4, the coherent pluggables support a set of read-
write attributes which are configurable. Example of such
configuration attributes are output power, central frequency and
operational-mode. Note that as discussed in Section 5.1, since a
coherent pluggable may support multiple operational-modes, as part of
these configuration attributes, operator should configure which of
these operational-mode is desired and should be functional.
Rokui, et al. Expires 22 April 2025 [Page 14]
Internet-Draft Modelling Optical Pluggables October 2024
|-----------------------------------------------------------------|
| optical-channel // OTSI channels |
| configuration // list of R/W plug configuration attributes |
| config-attribute-1 |
| config-attribute-2 |
| ..... |
| config-attribute-m |
| pm and states // list of R/O pm and state attributes |
| // Note-1: Each pm-attribute might have |
| // threshold definitions |
| // Note-2: For each monitored attributes, |
| // one SCTP profile can be assigned |
| monitored-attribute-1 |
| monitored-attribute-2 |
| ..... |
| monitored-attribute-p |
|-----------------------------------------------------------------|
Figure 4: Data structure for Coherent pluggable Configuration and
PM Attributes
5.3. Coherent Pluggable Performance Monitoring Data
Figure 4 shows the list of pluggable Performance Monitoring (PM) and
state data, which are critical components in optical networks,
enabling network engineers to ensure optimal performance, identify
issues, and maintain network reliability. Operators monitor a range
of attributes on both the optical/photonic and electrical sides of
coherent pluggables, including channel input power, channel output
power, central frequency, current Optical Signal-to-Noise Ratio
(OSNR), Bit Error Rate (BER), chromatic dispersion, laser
temperature, link status, and more. These parameters directly impact
the quality and integrity of the transmitted data across both optical
and electrical domains.
As coherent optical technology continues to gain traction, PM has
evolved to include more advanced techniques, such as monitoring the
quality of modulated signals and detecting impairments that could
degrade performance over long distances. By leveraging these PM
capabilities, engineers can ensure that the optical layer operates
effectively, optimize the utilization of optical resources, and
maintain high levels of service continuity and performance throughout
the network.
It is important to note that the "monitored attributes" encompass
parameters from the media side, host side, and hardware components of
coherent pluggables.
Rokui, et al. Expires 22 April 2025 [Page 15]
Internet-Draft Modelling Optical Pluggables October 2024
Performance Monitoring (PM) data is generated for various "monitored
attributes" by optical pluggables, representing a range of real-time
metrics, including current, average, minimum, and maximum values, as
well as counters and states. The PM data can be categorized as
follows:
* Basic Monitoring PM data: The analogue values which provide the
"current values" of a "monitored attributes" such as laser
temperature, eSNR (Effective Signal-to-Noise Ratio) at media
input, eSNR at host input, laser frequency error, and more.
* Advanced Monitoring PM data: The analogue values which provide the
"current, average, minimum, and maximum values" of "monitored
attributes" such as transmit signal power, Bit Error Rate (BER),
chromatic dispersion, etc.
* Up Counters: The discrete counter values of "monitored attributes"
that only increment, such as Bit Error Count, FEC (Forward Error
Correction) Uncorrected Errors, Loss of Signal (LOS) count, Loss
of Frame (LOF) count, and others.
* Up/Down Counters: The discrete counter values of "monitored
attributes" that can both incremented and decremented.
* Operational/Admin States: Represents the states of "monitored
attributes" such as link up/down state, alarm state, laser on/off
state, Automatic Power Control (APC) status, and more.
For "Up Counters" there might be two approaches:
* Continuous Increment: The counter value continuously increments
without resetting upon read.
* Reset on Read: The counter value resets either on read or based on
a predefined condition.
For "advanced monitoring performance management (PM) data", where
current, average, minimum, and maximum values are provided by the
coherent pluggable, a "windowing mechanism" is essential. Currently,
this mechanism is implemented by the host platform, not the pluggable
itself. For instance, the host platform utilizes the windowing
mechanism to segment the PM data collected by the coherent pluggable.
Within each window, the host calculates the minimum, maximum, and
average values of the PM data, enabling a granular and time-specific
analysis of the pluggable's performance.
Rokui, et al. Expires 22 April 2025 [Page 16]
Internet-Draft Modelling Optical Pluggables October 2024
A variety of performance monitoring metrics, including minimum,
maximum, average, and instantaneous values, can be collected. These
metrics offer a comprehensive view of performance fluctuations,
allowing for precise monitoring and quicker response times to
anomalies. Minimum and maximum values help identify the extremes of
performance, while average values give a sense of typical performance
levels. Instantaneous values, on the other hand, provide real-time
insights, which are crucial for immediate issue detection and
resolution. This multi-faceted approach ensures that network
performance is consistently monitored and maintained at high
standards.
Section 5.4 will discuss the collection type and how they are related
to the above-mentioned PM data. It also covers the coherent
pluggables support for threshold crossing alerts (TCA) for all or a
subset of monitored attributes.
5.4. Coherent Pluggable Threshold Definition
As indicated in Section 5.3, coherent pluggables are capable of
providing the threshold crossing alert (TCA) for all or subset of
"monitored attributes". In this situation, the coherent pluggable
raises an alert which informs the host about operationally undesired
situations or about critical threshold crossings of monitored
attributes. The coherent pluggable raises an alert by setting an
associated Flag on pluggable memory-map that represents the alert.
As mentioned previously, the TCA might be supported for a subset of
coherent pluggable monitored attributes. Since it is possible that
the coherent pluggable has different capabilities to raise threshold
for different monitored attributes, to provide a general solution for
threshold definition on coherent pluggable monitored attributes, this
draft introduces the concept of "Supported Collection and Threshold
Profile (SCTP)" shown in Figure 5 which defines the configurable
threshold values and collection types (i.e., the collection of
current value, average value, min/max value are supported). The SCTP
types will be used in list of coherent pluggables Sheet.
To define the warning, minor, major, critical threshold values for a
coherent pluggable monitored attribute, operator should set upper and
lower limits that delineate acceptable performance ranges. This
ensures that any deviations can be quickly identified and addressed.
A rolling window between min-time and max-time should be employed to
dynamically adjust these thresholds based on recent data trends,
providing a more accurate reflection of current network conditions.
By continuously updating the thresholds, network performance can be
maintained within optimal parameters, reducing the risk of undetected
issues.
Rokui, et al. Expires 22 April 2025 [Page 17]
Internet-Draft Modelling Optical Pluggables October 2024
Note that sometimes these thresholds are configurable and sometime
they are hard-coded. It is also possible that a vendor can support a
sub-set and super-set of monitored attributes (for super-set they
need to augment the yang model).
Supported-Collection-and-Threshold-Profile (SCTP)
|----------------------------------------------------------------|
| SCTP-Type-1: |
| Collection: current, average, min, max |
| Configured Threshold: warning, minor, major, critical |
| |
| SCTP-Type-2: |
| Collection: current |
| Configured Threshold: warning, minor, major, critical |
| |
| SCTP-Type-3: |
| Collection: current, average, min, max |
| ... |
| SCTP-Type-n: |
|----------------------------------------------------------------|
// Note: These are just a few examples. More SCTP profile
// can be defined
Figure 5: Coherent pluggable Collection and Threshold Profile
Definition
5.5. Coherent Pluggable Alarm Notifications
[Editor's note: To be added in a later release.]
The coherent pluggables might generate various alarm notifications
due to the various reasons.
5.6. Support of Vendor-Specific Attributes
In some instances, a coherent pluggable may support attributes that
are specific to a vendor. These are vendor-specific attributes which
should be supported by the host. In most cases the host packet
device does not understand the semantics of these vendor-specific
capability attributes but should be able to understand their syntax
and communicate them to the SDN controller.
Note that these vendor-specific attributes could be
* read-only capability attributes
* read-write configuration attributes or
Rokui, et al. Expires 22 April 2025 [Page 18]
Internet-Draft Modelling Optical Pluggables October 2024
* read-only performance monitoring attributes.
As part of coherent pluggable work, we need to address this situation
where a vendor has proprietary attributes which need to be configured
on coherent pluggables or read from them. In this situation we also
need to address how the proprietary attributes are treated by both
host and internal protocol between host and pluggable (i.e., CMIS
protocol). This allows different coherent pluggables to be used in
various multi-vendor hosts (e.g., routers) in plug-and-play fashion.
To achieve this, the coherent pluggable YANG data model (the work
done as part of this draft - Google Sheet) should first be augmented
with vendor proprietary capability, configuration or PM attributes.
As noted above, it might be also necessary to define how these new
attributes are mapped to the internal protocol between the host and
the pluggable via CMIS protocol. A key consideration is that the
host does not need to understand the semantics of these new
attributes and may not even need to know their syntax.
Another consideration is the privacy of vendor specific attributes,
i.e., these proprietary attributes may be commercially sensitive. It
would be quite reasonable to encrypt the related properties allowing
for them to be passed to a specific vendor control component without
being observed or interpreted in any way by other control components
(from other vendors).
There are multiple solutions to this problem which will be discussed
below. To demonstrate these solutions, consider the host Vendor-X
and pluggable Vendor-Y in Figure 1. Let's assume:
* Vendor-Y has a new read-write proprietary configuration attributes
"AA" which should be configured in pluggable (in addition to well-
known attributes such as central-frequency, power and operational-
mode). The value of attribute AA is 100 and its memory map in
coherent pluggable is 0x1100.
* In addition, consider a new read-only proprietary capability
attributes "CC" supported on pluggable in range of {CC-min, CC-
max}={1.1,3.3}.
5.6.1. Vendor-Specific Capability Attributes
The coherent pluggable YANG data model is augmented with a list of
new capability attributes. As demonstrated in Figure 6, the YANG
data model is augmented with the following information:
* ID of new capability proprietary attribute
Rokui, et al. Expires 22 April 2025 [Page 19]
Internet-Draft Modelling Optical Pluggables October 2024
* Name of new capability proprietary attribute
* Minimum value of new attribute
* Maximum value of new attribute
The Figure 6 shows an example of new capability attribute "CC" whose
min and max values are 1.1 and 3.3, respectively.
+--ro vendor-specific-capability-attribute-list* [cap-attribute-id]
+--ro cap-attribute-id uint32
+--ro cap-attribute-name string
+--ro cap-min-value decimal64
+--ro cap-max-value decimal64
1
CC
1.1
3.3
Figure 6: Support of Vendor-Specific Capability Attributes
To support the vendor-specific configuration attributes, there are a
few potential solutions which are discussed below.
5.6.2. Vendor-Specific Configuration Attributes (Solution-1)
This approach is the simplest solution, as it requires no
interpretation by the host platform. The coherent pluggable YANG
data model is augmented with a list that directly maps the values of
new configuration attributes to the corresponding memory-map
locations on the pluggable device. In this solution, the memory-map
locations must be known to the operator, potentially provided in the
Coherent Pluggable Manifest. The Figure 7 illustrates the coherent
pluggable YANG data model, which has been augmented with the
following information:
* ID of new proprietary configuration attribute
* Name of new proprietary configuration attribute
* Value of new proprietary attribute
* The memory map of new proprietary attribute (which is used in CMIS
communication between host and pluggable)
Rokui, et al. Expires 22 April 2025 [Page 20]
Internet-Draft Modelling Optical Pluggables October 2024
For instance, consider a scenario where the operator intends to
configure a new proprietary attribute, "AA," with a value of 100, and
a memory-map location on the pluggable set to 0x1100. In this
process, the host platform receives the attribute "AA" as defined in
Figure 7. The host platform then relays this information to the
coherent pluggable via the CMIS protocol, without performing any
interpretation. In other words, the host platform is not required to
understand the syntax or semantics of these attributes; it functions
merely as a conduit, transmitting the values from the NBI to the
designated memory-map locations on the pluggable.
+--rw vendor-specific-config-attribute-list* [conf-attribute-id]
+--rw conf-attribute-id uint32
+--rw conf-attribute-name string
+--rw value decimal64
+--rw memory-map decimal64
1
AA
100
1100
Figure 7: Solution-1 for support of vendor proprietary config
attributes
5.6.3. Vendor-Specific Configuration Attributes (Solution-2)
This approach is similar to Figure 7 but requires the host platform
to implement lookup logic to determine the memory-map location on the
pluggables. In this solution, the coherent pluggable YANG data model
is augmented with the following new attributes, as shown in Figure 8:
* ID of new proprietary configuration attribute
* Name of new proprietary configuration attribute
* Value of new proprietary attribute
The operator does not have visibility into the specific memory-map
locations for these attributes on the coherent pluggable device.
Instead, the memory-map for each new attribute is provided in the
Coherent Pluggable Manifest. In this scenario, the host platform
must search the pluggable manifest to locate the corresponding
memory-map location for each new attribute. These values are then
communicated to the pluggable via the CMIS protocol for
configuration. As in Figure 7, the host platform does not need to
Rokui, et al. Expires 22 April 2025 [Page 21]
Internet-Draft Modelling Optical Pluggables October 2024
understand the syntax or semantics of the new attributes; it only
needs to search the pluggable manifest to identify the memory-map
locations for the new attributes.
As illustrated in Figure 8, the host platform receives the new
attribute "AA" via its Northbound Interface (NBI), with a
configuration value of 0x1100. The host then searches the coherent
pluggable manifest to determine the memory-map location associated
with this attribute and identifies it as 0x1100. Without
interpreting the attribute's syntax or semantics, the host platform
communicates this information to the coherent pluggable via the CMIS
protocol. Essentially, the host platform functions as a proxy,
transmitting the values from the NBI to the appropriate memory-map
locations on the pluggable without needing to understand the meaning
of the attributes.
+--rw vendor-specific-config-attribute-list* [conf-attribute-id]
+--rw conf-attribute-id uint32
+--rw conf-attribute-name string
+--rw value decimal64
Note: The memory-map for each new attribute is provided in
pluggable Manifest.
1
AA
100
Figure 8: Solution-2 for support of vendor proprietary config
attributes
5.6.4. Vendor-Specific Configuration Attributes (Solution-3)
This solution represents an advanced approach when a new vendor-
specific proprietary configuration attribute is mapped to multiple
memory-map locations on a pluggable device, or when multiple such
attributes are mapped to a single memory-map location on pluggable.
Similar to Figure 8, the mapping between these new attributes and
their corresponding memory-map locations should be detailed in the
pluggable manifest. For each new vendor-specific attribute, the host
platform is required to perform a lookup in the pluggable manifest to
identify the relevant memory-map locations. The platform then
assembles the corresponding values, which are communicated to the
pluggable device via the CMIS protocol.
Rokui, et al. Expires 22 April 2025 [Page 22]
Internet-Draft Modelling Optical Pluggables October 2024
Although this solution is included for completeness, it is not
practical or desirable due to its complexity and the need for
interpretation by the host software
5.6.5. Vendor-Specific Secret Capability Attributes
to be added
5.6.6. Vendor-Specific Secret Configuration Attributes
There are situations where vendor-specific configuration attributes
are confidential, and the vendor wishes to conceal their meanings and
values. When considering the interface from the pluggable device to
the host via CMIS, it is crucial that the pluggable does not expose
the meaning or value of these confidential attributes. Ideally, the
pluggable device would encrypt the data. Within the context of CMIS,
it may be sufficient to allocate an array of register locations to
convey the property values. These registers would store an encrypted
data blob for read-only properties and accept an encrypted blob for
writable registers. The specific value might be set or read through
different register positions on each read/write, depending on the
encryption technique used.
It is important to note that since the pluggable device encrypts the
data, mapping the data offers no additional benefit. The YANG model
would simply convey the register values as requested. The properties
are applied to the memory map in a manner that may appear disordered.
The location values must always be read together and written as
specified, potentially requiring multiple reads to retrieve all
properties. This approach could be incorporated into the basic
register-based option discussed in Section 5.6.2.
As an example, let's assume a vendor defines secret attribute "DD"
for its coherent plggable. Vendor first needs to augment IETF data
model with a list of encrypted values and memory-maps shown in
Figure 9. This very similar to Figure 7 where essentially the host
functions as a proxy, transmitting the values from the NBI to the
appropriate memory-map locations on the pluggable without needing to
understand the meaning and semantics of these attributes.
+--rw vendor-specific-config-attribute-list* [conf-attribute-id]
+--rw conf-attribute-id uint32
+--rw encrypted-attribute-name string
+--rw encrypted-attribute-value string
+--rw memory-map decimal64
Figure 9: Solution-4 for support of vendor secret attributes
Rokui, et al. Expires 22 April 2025 [Page 23]
Internet-Draft Modelling Optical Pluggables October 2024
5.6.7. Support of Vendor-Specific Performance Monitoring Data
As with any vendor-specific/proprietary property, the additional
support is defined in the manifest. The host is informed of the
properties via YANG augments and appropriate mapping definitions.
The mapping definitions tell the host that the related properties are
related to performance monitoring data such that the host will
periodically read the appropriate parts of the pluggable interface as
for any other performance monitoring data. AS for all other
performance monitoring data, the host does not need to understand the
data. The client controller can carry out analysis or can propagate
the measures transparently to some other controller etc.
6. Coherent Pluggables Yang Data Model
As discussed in the sections on capabilities, configuration, and
performance monitoring in Section 5.1, Section 5.2, and Section 5.3,
the coherent pluggable module includes various read-only capability
attributes, read-write configuration attributes, and read-only
performance monitoring attributes. For a comprehensive list of these
attributes, refer to the accompanying coherent pluggable Google Sheet
(Q: how can we incorporate the Google Sheet?).
Considering the next step involves converting the Coherent Pluggable
Google Sheet into the 'Coherent Pluggable YANG data model', this
draft proposes utilizing the methodology outlined in Figure 10 for
each attribute within the Google Sheet. The primary objective of
this approach is to categorize the attributes associated with
coherent pluggables. These attributes may fall under supported
capabilities, configuration, or performance monitoring (PM)
attributes. Here are a few examples:
* The read-write attributes "channel-output-power" and "central-
frequency" are supported attributes that can be configured, and
the coherent pluggable can collect PM data and assign PM
thresholds to them.
* The read-only attribute "chromatic-dispersion", which is solely
part of the supported capabilities and PM attributes. This
attribute cannot be configured on coherent pluggables.
* The read-only attribute "supply-voltage" could be considered,
which is exclusively part of the PM attributes. It neither falls
under supported capabilities nor is it a configurable attribute.
Rokui, et al. Expires 22 April 2025 [Page 24]
Internet-Draft Modelling Optical Pluggables October 2024
// To convert the "Coherent Pluggable Google Sheet" to
// "Coherent Pluggable Yang Data Model", apply the following
// methodology to all attributes in "Coherent Pluggable Google Sheet"
// Note: This example uses attribute "channel-output-power" just
// as an example.
// This methodology provided is applicable to any attributes.
channel-output-power{
is-capability-attributes = (TRUE or FALSE)
{
// if "TRUE", the following needed to be added
ro min-channel-output-power = ...
ro max-channel-output-power = ...
ro default-channel-output-power = ...
}
is-configurable = (TRUE or FALSE)
{
// if "TRUE", this is R/W attribute
rw channel-output-power = ...
}
is-monitorable = (TRUE or FALSE)
{
// if "TRUE", following PM data from pluggable might
// be available and can be read
ro current-channel-output-power (if applicable)
ro average-channel-output-power (if applicable)
ro min-channel-output-power (if applicable)
ro max-channel-output-power (if applicable)
}
is-threshold-available = (TRUE or FALSE)
{
// if "TRUE", following PM thresholds might be configurable
rw threshold-for-warning-alert (if applicable)
rw threshold-for-minor-alert (if applicable)
rw threshold-for-major-alert (if applicable)
rw threshold-for-critical-alert (if applicable
}
}
Figure 10: Coherent pluggable Data Yang Model
Rokui, et al. Expires 22 April 2025 [Page 25]
Internet-Draft Modelling Optical Pluggables October 2024
7. Coherent Pluggable Data Modeling Gap Analysis
This draft on "coherent pluggable data model and gap analysis" was
initiated to examine existing IETF models related to pluggables for
"completeness" to assess existing IETF properties/structures which
are relevant to coherent pluggables and also to look for missing
properties/structures. The goal of current work is to achieve best
positioning of the IETF work with respect to the other related
activities in the industry.
To carry out this ongoing examination, properties/structures from
relevant external bodies are collected and compared with properties/
structures present in IETF models related to coherent pluggables.
Where properties/structures differ the differences are examined and
justifications considered and justification provided for changes to
the IETF models these are proposed.
The following items are identified as gap related to coherent
pluggables:
* Syntax gaps: Naming inconsistency on existing IETF drafts
[ietf-impairment-yang], [ietf-layer0-yang] and
[ietf-optical-interface-yang]. As an example, the capability
attribute "max-channel-input-power" is also referred to as "rx-
channel-power-max". We need to fix this. This draft proposes the
following structure (note that there will be multiple valid
proposals).
Naming convention:
direction [tx/rx/both/none]-
[name of the attribute]-
value [min / max / current / none]
Examples:
for IETF attribute rx-channel-power-max, use
rx-channel-power-max (no change)
for ITU-T attribute "Minimum (residual) chromatic dispersion", use
residual-chromatic-dispersion-min
for IETF attribute "max-central-frequency", use
central-frequency-max
for IETF attribute "channel-output-power", use
tx-channel-power
Rokui, et al. Expires 22 April 2025 [Page 26]
Internet-Draft Modelling Optical Pluggables October 2024
* Semantic gaps: For a complete solution for coherent pluggable, the
capabilities, configuration, PM attributes and PM thresholds
supported by IETF coherent pluggable should be consistent with
coherent pluggable attributes supported by [OIF-CMIS]. This needs
fuhrer investigation.
* Statement of Capability: For any attribute defined in IETF drafts
[ietf-impairment-yang], [ietf-layer0-yang] and
[ietf-optical-interface-yang] which is configurable or is
measurable and threshold can be set, we need a capability
statement.
* [Editor's note: More to be added .]
8. Coherent Pluggable Manifest
Referring to Section 5.1, the coherent pluggable capability
attributes (i.e., supported-modes) are crucial aspects of coherent
pluggables and should be easily accessible for various reasons and
activities. Those might include:
* Network Engineers: Network engineers needs to know the
capabilities and characteristics of any coherent pluggable whether
the coherent pluggable is already deployed or will potentially be
installed and deployed in their network
* SDN Controllers: The optical, packet or higher-layer SDN
controllers need to have detailed knowledge of the coherent
pluggables for various reasons such as network planning, viability
assessment of the photonic services from plug-to-plug,
configuration and performance monitoring collection, alarm
notifications etc.
* Packet Device (e.g., Router): Optionally the host packet device
need also access to coherent pluggable capabilities to provide
details of coherent pluggables already installed in packet devices
for example during the debugging and troubleshooting of
pluggables.
To facilitate the utilization of coherent pluggable attributes, this
draft introduces the concept of the "Coherent Pluggable Manifest."
The manifest serves as a comprehensive collection of information that
is appropriately structured and interrelated, providing a detailed
description of the capabilities of a pluggable device. In
alternative terminology, the manifest may also be referred to as a
Specification, a Profile, or a Plug database, among other terms.
Rokui, et al. Expires 22 April 2025 [Page 27]
Internet-Draft Modelling Optical Pluggables October 2024
It should be noted that any equipment could have a Manifest
describing its capabilities and the Manifest may be broken down into
units that can be referenced and reused, i.e., the definition can be
modular. To facilitate the stages, each vendor would be expected to
provide a Manifest for each pluggable type & version.
A pluggable type & version may offer a subset of standard
capabilities. The subset is described by simply omitting
definitions.
A pluggable type & version may offer a super-set. The super-set is
detailed by adding definitions via "augmentation" to the set of
standard definitions available for use in the matiest. These
capability augmentations relate to augmentations to the YANG model
used at the interface to the host. Note that host has no need to
understand the semantics of the augmented properties, but does need
to know the mapping to the pluggable interface. This is discussed in
more detail elsewhere in this document.
We should also consider the fact that some proprietary attributes and
capabilities of the coherent pluggable might be commercially
sensitive and hence confidential and a vendor might not want to
provide it to publicly to everyone. In other words, some guidelines
and restriction might be applicable to some portion of "Coherent
Pluggable Manifest". To provide more security, the access to the
pluggable manifest could be restricted or password protected and
potentially encrypted. It is also possible to provided restrict
access to an operator or a team or group of people of an operator
where there may also be a requirement for an NDA to enable access to
the data. It is also possible that the encrypted section of the
Manifest might only be passed to a specific vendor control component
(without being meaningfully observed by other control components from
other vendors). The encrypted information may be passed via a
special secure channel directly to a component authorized to decrypt
the information into machine interpretable form and use it.
Considering the above, it appears reasonable that all pluggable
capabilities whether they be proprietary or standard should be fully
described in the Manifest (considering that some portions of the
Manifest might have restrictions as previously described). This may
be achieved by a reference to a standard that is itself fully defined
in machine interpretable form. This approach would allow for a far
more flexible and future-proofed control solution.
In summary, to facilitate easy access to coherent pluggable
attributes, the details of coherent pluggable operational-modes are
collected in a repository (access restriction might be applicable to
some portions of this document), such as GitHub and SharePoint,
Rokui, et al. Expires 22 April 2025 [Page 28]
Internet-Draft Modelling Optical Pluggables October 2024
called "Coherent Pluggable Manifest". The manifest must be both
human and machine-readable repository and can be read and interpreted
easily by any SDN controller, operators, or other devices in the
network. A manifest contains multiple records which are uniquely
identified by tuple [organization-id, operational-mode].
The manifest contains four sections:
* Photonic/Optical capability section: This section contains all
photonic/optical capabilities of the coherent pluggable and
identifies all read-only attributes. It also allow augmentation
of this section for vendor-specific attributes.
* Configuration attributes: This section contains all read-writer
attributes which can be configured on coherent pluggable. It also
allow augmentation of this section for vendor-specific
configuration attributes.
* PM Collection style for monitored attributes: List of all read-
only monitored attributes where the coherent pluggable can collect
PM data. This section identifies if the collection of current,
average, min and max values are possible.
* PM Threshold values: For all or a subset of read-only monitored
attributes, this section contains the threshold settings for
threshold crossing alerts (TCA) if applicable.
Figure 11 illustrates the overall structure of the "Coherent
Pluggable Manifest". It contains several operational-mode records
where each record includes all the capability attributes for tuple
[organization-id, operational-mode]. As discussed in Section 5.1,
"organization-id" refers to any authority that defines these
attributes such as ITU-T [G.698.2] or [OIF-400ZR]) or an individual
vendor.
Each record in the coherent pluggable manifest is machine readable/
interpretable and is uniquely identified by a tuple [organization-id,
operational-mode].
Using "Coherent Pluggable Manifest", the format of all operational-
modes are identical whether it is defined by for example ITU-T, OIF,
OpenConfig, or defined by a vendor.
Rokui, et al. Expires 22 April 2025 [Page 29]
Internet-Draft Modelling Optical Pluggables October 2024
A record identified by
tuple [organization-id, operational-mode]
|--------------------------------------------------------|
| |-|
| organization-id: (e.g., ITU-T, OIF or Vendor) | |-|
| operational-mode: (described in this draft) | | |
| (see also Google Sheet) | | |
| version: | | |
| | | |
| Photonic/Optical capabilities attributes | | |
| ----------------------------------------- | | |
| (i.e., Read-only attributes defined in | | |
| operational-mode of this draft. For each attribute, | | |
| min, max, default values might be available) | | |
| - attribute A1 | | |
| - attribute A2 | | |
| ... | | |
| - attribute An | | |
| - List of vendor-specific capability attributes | | |
| (augmented yang model) | | |
| | | |
| Configuration attributes | | |
| -------------------------- | | |
| ( The list of all read-write attributes where | | |
| can be configured on coherent pluggables ) | | |
| are possible ) | | |
| - attribute C1 | | |
| - attribute C2 | | |
| ... | | |
| - attributeCWm | | |
| - some vendor specific config attributes | | |
| (augmented yang model) | | |
| | | |
| Monitored attributes PM collection | | |
| ------------------------------------ | | |
| (i.e., list of monitored attributes where | | |
| coherent pluggable can collect PM data for | | |
| current, average, min, max values) | | |
| - attribute M1 | | |
| - attribute M2 | | |
| ... | | |
| - attribute Mp | | |
| | | |
| Monitored attributes Threshold setting | | |
| --------------------------------------- | | |
| For all or some attribute M1,... Mp, define | | |
| - threshold-for-warning-alert (if applicable) | | |
Rokui, et al. Expires 22 April 2025 [Page 30]
Internet-Draft Modelling Optical Pluggables October 2024
| - threshold-for-minor-alert (if applicable) | | |
| - threshold-for-major-alert (if applicable) | | |
| - threshold-for-critical-alert (if applicable) | | |
| | | |
|--------------------------------------------------------| | |
|--------------------------------------------------------| |
|--------------------------------------------------------|
Coherent Pluggable Manifest
- Contains one or more operational-mode records
- Each record for tuple [organization-id, operational-mode]
- It is machine-readable/interpretable
Figure 11: Coherent Pluggable Manifest
Below are several examples that demonstrate the concept of the
"Coherent Pluggable Manifest." Figure 12 illustrates the content of
a manifest record for operational mode 0x3E, as defined by the OIF
forum. This operational mode is widely recognized and supported by
nearly all coherent pluggable devices. Detailed information
regarding this operational mode can be found in [SFF8024], Table 4-7.
organization-id: OIF
operational-mode: 0x3E
// Photonic/Optical capabilities attributes
list of attributes
modulation: DP-16QAM
bit-rate: 478.75 Gbps
baud-rate: 59.84375 Gbd
more attributes ...
// Configuration attributes
// Monitored attributes PM collection
// Monitored attributes Threshold setting
Figure 12: Coherent Pluggable Manifest Defined by OIF
Figure 13 is anther manifest record where the Vendor-X has defined
the operational-mode 0x22. In this case, Vendor-X defines all the
attributes related to this operational-mode, which might not be
supported by other pluggable vendors.
Rokui, et al. Expires 22 April 2025 [Page 31]
Internet-Draft Modelling Optical Pluggables October 2024
organization: Vendor-X
operational-mode: 0x22
// Photonic/Optical capabilities attributes
list of attributes
modulation: 16-QAM
bit-rate: 400 Gbps
baud-rate: 56 GBd
more attributes ...
// Configuration attributes
// Monitored attributes PM collection
// Monitored attributes Threshold setting
Figure 13: Coherent Pluggable Manifest Example-2
"Figure 14" presents an example where the Vendor-Y defined an
operational-mode 0x22 as well. In this scenario, the organization
associated with the pluggable module is Vendor-Y, which defined the
same operational-mode 0x22 as "Vendor-X"
It is important to note that while the operational-modes in both
Figure 13 and Figure 14 share the same values, they are defined by
different vendors. Consequently, these operational-modes are not
related and may differ significantly in their attributes. In other
words, although the semantics of these modes are identical, their
actual content might vary significantly. This is one of the reasons
that any record in Coherent Pluggable Manifest is uniquely identified
by tuple [organization-id, operational-mode].
organization: Vendor-Y
operational-mode: 0x22
// Photonic/Optical capabilities attributes
type: NON-STANDARD
list of attributes
modulation: QPSK
bit-rate: 800 Gbps
baud-rate: 96 GBd
more attributes ...
// Configuration attributes
// Monitored attributes PM collection
// Monitored attributes Threshold setting
Figure 14: Coherent Pluggable Manifest Example-3
Rokui, et al. Expires 22 April 2025 [Page 32]
Internet-Draft Modelling Optical Pluggables October 2024
9. Optical Pluggables Lifecycle Management
This section discusses the complete lifecycle of an optical pluggable
as shown in Figure 15. It includes discussion on the pre-purchase
evaluation of pluggables through installation to the operation of a
pluggable in a live network.
Most of this lifecycle discussion applies to a majority of equipment
types. Where the pluggable is special, this is highlighted.
The figure below provides a high level flow. In a real environment,
all stages will be running in parallel for various plug versions etc.
and there may be feedback from any stage to a previous stage. For
example, the research, evaluation and planning exercises are ongoing
activities that continue as the network grows and changes and as new
pluggable type & versions are introduced by vendors and insight from
deployment may feed back to the evaluation stage.
Throughout the lifecycle specific use cases and scenarios will be
considered and applied. These will be developed during the early
stages and applied in service design.
Note: The stages and the terminology used are not intended to reflect
any specific operational practice. They are intended to be neutral
with respect to any existing operator's processes, aligning with the
essence of the processes.
Market research \
| |
v |
Testing of pluggable samples | Refer to
| | Section 9.1
v |
Trials & PoCs |
| |
v |
Approve pluggable type /
| ---------
v \
Service demand Analysis |
| |
v | Refer to
Network planning | Section 9.2
| |
v |
Service type realization analysis |
| |
v |
Rokui, et al. Expires 22 April 2025 [Page 33]
Internet-Draft Modelling Optical Pluggables October 2024
Purchase pluggables /
| ---------
v \
Optical infrastructure creation |
| |
v |
Service demand received | Refer to
| | Section 9.3
v |
Design service |
| |
v |
Validate optical design /
| ---------
v \
Work Order (physical) |
| |
v |
Installation of pluggables etc. |
| | Refer to
v | Section 9.4
Service configuration |
| |
v |
Service validation & test |
| |
v |
Enable Service |
| |
v |
Operate service /
Figure 15: Lifecycle of a coherent pluggable
The following sub-sections discuss the overall flow of activities and
then work through the lifecycle stages in some detail.
9.1. Approving the pluggable type and version
Pluggables, like all equipment, are carefully chosen. A network
operations company (the operator) will decide what pluggables to use
in the network based upon research and an understanding of
capabilities of the pluggables available in the marketplace. These
capabilities will be considered against the specific applications,
use cases and scenarios that are of relevance to the operator's
business.
Rokui, et al. Expires 22 April 2025 [Page 34]
Internet-Draft Modelling Optical Pluggables October 2024
It is expected that these applications, use cases and scenarios will
be developed through "Market research" and as pluggables etc. are
assessed. The use cases and scenarios will be applied extensively in
later stages.
The operator will acquire samples of each type & version of pluggable
of interest and probably test and then trial them. They will also
probably carry out "type approval" considering each type&version of
pluggable for a particular set of applications (where those
applications may be defined by the operator themselves or may be
standardized definitions) etc. The full detail of the capability of
each type & version of pluggable is relevant at all of these stages
(see Section 9.5). The capabilities are expected to be expressed in
a Manifest (see Section 8).
The market analysis will lead to Service type design (some of which
will be innovative) and will lead to an understanding of potential
revenue. This revenue prediction will be considered when evaluating
price and compatibility such that initial sketches of use can be
constructed.
9.2. Planning the network
Specific pluggables (type&version) will be purchased only after
detailed planning of the network. To carry out this planning, full
knowledge of each type&version of pluggable will be required. The
planning process will account for key pluggable properties to explore
viability and compatibility. The planning will use predictions of
"service demand" (e.g., using a demand matrix) and hence
infrastructure need to determine purchase volumes, phasing etc.
The exercise may result in identification of several type & versions
of pluggable that can be interchanged for a particular specific
purpose. Clearly, pluggable pricing will also be accounted for in
this phase. Again, during this stage of the lifecycle the full
detail of the Manifest for each type & version of pluggable is
relevant.
During the "Network planning" process different types of service
relevant for the applications, use cases and scenarios (identified in
Section 9.1) will be explores and specific approaches to realizing
each resulting type of service will be determined. This will result
in design of specific "service realization" patterns and templates
that will be used in later stages of the process. The approach to
deploying each service type is defined for each operational context
(application etc.)
Rokui, et al. Expires 22 April 2025 [Page 35]
Internet-Draft Modelling Optical Pluggables October 2024
As a result of the planning exercise, numbers of each pluggable
type&version required will be known and purchasing can be initiated.
The purchased pluggables will be added to the inventory and spares
holdings.
9.3. Dealing with service demand
The planning exercise leads to optical infrastructure requirements
with some timetable for deployment. The "Optical infrastructure" is
designed (using the patterns/templates designed in Section 9.2. The
infrastructure will be deployed as appropriate based upon predicted
and actual service demand etc.
When optical "services demand" is received, perhaps to provide
underlay for the packet network or driven by a specific service
contract, optical network analysis is carried out to evaluate how to
efficiently and effectively achieve the specific service demanded.
This analysis will consider the whole optical network including the
plugs and ROADMs etc. In most cases this "Service design" will use
patterns/templates constructed in Section 9.2 in conjunction with
relevant capability information for the pluggable type&version.
Prior to progressing further it is important to note that pluggables
are highly valuable, and correspondingly expensive. They are
deployed in a controlled fashion. There are a range of policies for
deployment of pluggables.
In some cases, at one extreme end of the range of policy choices, an
operator may decide to fully populate a packet device with a
selection of pluggables and may cable them to adjacent ROADMS.
However, it is more likely that pluggable deployment will be on a
just-in-time basis, at the other end of the range of policy choices,
so a pluggable is not deployed (and hence is not cabled) until the
solution to realization of the optical service has been determined.
Regardless of the pluggable deployment approach, the pluggable
capability will be accounted for in the optical network analysis
activity. Where pluggables are present, the range of installed
pluggables constrain the possible realizations, where the pluggables
have not been deployed all approved pluggables (type&version) could
be considered during the analysis, although capability of the
relevant packet devices to support specific pluggables will also need
to be considered, and this may eliminate some pluggables. In
addition, if there is some urgency, the availability of the type of
pluggable to the installation engineer and/or in the local spares
holding inventory may also be considered.
Rokui, et al. Expires 22 April 2025 [Page 36]
Internet-Draft Modelling Optical Pluggables October 2024
The optical design will be "validated" in terms of "viability" and
compatibility prior to proceeding. This analysis takes into account
the full definitions of the pluggable type&versions of interest,
where each is defined in a corresponding and referenced manifest.
9.4. Installing and operationalising the pluggable
Once the design is available, any necessary physical installation
exercise (pluggable installation, cabling etc.) is carried out,
driven by "Work orders" that identify the type&version of pluggable
to instal etc.
On detection of the pluggable instance, the control system will
validate that the work order has been carried out correctly. To do
this, the full type&version of the pluggable is read and compared
with the intent. Where there are discrepancies, either a work order
is constructed to correct the installation error after the detected
pluggable type&version is evaluated for compatibility with the
specific design. This evaluation is done using the Manifest for that
type&version. It is possible that the type&version may be acceptable
although perhaps a little more expensive than the optimum choice etc.
Once the type&version of pluggable has been confirmed, the cabling to
the pluggable will be validated and the service set up and validated.
Depending upon the operator practices, there may be an extensive
service test phase prior to handing over the service. The service
may not be enabled immediately, but will be at some point after which
the service will become operational. From this point on, normal live
service/equipment management/control will be active.
Beyond this point normal operational activities such as engineering
works, restoration, upgrade, fault location etc. will be carried out.
Clearly, there is also the reverse sequence which includes
deactivating a service and removing the plug and there are also
various edits and refinements that result from changes in demand and
changes in understanding of the service needs etc. These steps have
not been covered at this stage as the initial list above is
sufficient to the develop a deep understanding of the control of the
plugs. Further stages will be added in a future version of this
document.
In addition, during transition towards a more automated future, there
are processes related to discovery of existing network etc. In many
of these processes the current state of the network is understood
including the type&version of each pluggable. Some degree of
understanding of capability of pluggables (and any other equipment)
is relevant. The approach using manifests appears appropriate to
gain this understanding.
Rokui, et al. Expires 22 April 2025 [Page 37]
Internet-Draft Modelling Optical Pluggables October 2024
9.5. Expressing capabilities
As highlighted above, prior to installation of an optical pluggable
in a device (with packet functions etc.), various research, approval,
planning and design activities must be carried out (as they would be
for any hardware). All of these activities will require information
on the capabilities of the pluggable.
Detailed information on the capability of the pluggable is required
long before it is installed and operating. This points to the need
for a model of capability (of a type of pluggable) that is
independent of the model of a running instance (and hence points to
decoupling of the model of capability from the model of the operation
of the pluggable). This also suggest that discovery of capability
detail from the pluggable is not sufficient/appropriate for
deployment (although it may be useful in a lab context).
A machine interpretable definition/specification for the pluggable
should be available (independent of the pluggable instance) for each
pluggable type&version where the statement of type&version (complete
type&version) used is to the degree sufficient to precisely identify
the relevant (unique) definition/specification. The complete
type&version may include hardware type&version, firmware type&version
and software type&version details (where the firmware/software
influences the operation/control of the pluggable). This is
essentially the type&version used when considering spares holding and
like-for-like replacement in the field.
From this perspective, all that is required from a running pluggable
is to report the complete type&version detail so that this can be
confirmed as the right type&version. The type&version can be used to
reference the relevant unique specification.
It is important to clarify the definition of capability. In this
document, the term capability means "A quality or facility that
enables something to carry out some activity and/or take some role".
In the context of an equipment, the term applies to its functional
and physical properties.
Considering a pluggable (as for many other equipments), this would
include specification of capabilities such as:
* physical size, form factor and shape (the capability to fit in a
particular type of location)
* connector type (the capability to physically interconnect with a
compatible connector)
Rokui, et al. Expires 22 April 2025 [Page 38]
Internet-Draft Modelling Optical Pluggables October 2024
* bus architecture (the capability to communicate with a compatible
component)
* optical termination characteristics (the functional capabilities
emergent from the powered physical equipment, allowing
interconnection with corresponding compatible functions)
* measurement opportunities (the functional capabilities to provide
information to various control functions)
A capability statement may be a precise single value with no
uncertainty, a range, a collection of related ranges and thresholds
etc. Where some aspect has variability or is controllable, this is
also required to be specified.
For an equipment to be understood and used by a control system, the
detailed information on capabilities must be available in machine
interpretable form (to the degree necessary for any particular
function to be carried out). The machine interpretable statements
may be in the form of software, but preferably should be in the form
of data (information) that can be readily ingested by tooling and
ideally in a standardised language.
Traditionally, the published statements of capability have been in
somewhat ambiguous text that require interpretation and conversion
into a machine interpretable form through a manual intermediate step
(normally performed, with errors and performed many times for any
particular device type etc.). It is suggested here that the best
source of the machine interpretable data is the specifying authority
(e.g., ITU-T for standard applications, the vendor for plug
capabilities, an operator for non-standard applications).
10. Implications for the Functional Control Architecture
[Editor's note: To be added in a later release.]
The following section considers the interaction sequence, resulting
from the pluggable lifecycle analysis, within the functional control
architecture and highlights resulting adjustments to the control
functionality. Note that this section does not deal with the
physical realization of the control components of the functional
architecture other than those dependent on the device and pluggable
physical boundaries.
11. Usage of Coherent Pluggables Manifest
Within this section, we present a few use-cases showcasing the
practical application of the coherent pluggable manifest.
Rokui, et al. Expires 22 April 2025 [Page 39]
Internet-Draft Modelling Optical Pluggables October 2024
11.1. Example-1: Coherent Pluggables Manifest
The first example is illustrated in Figure 16. This is a simple
example where the packet over optical network has been already
provisioned with both optical underlay and packet overlay services.
The role of SDN controller is just to discover and manage the
network. In other words, the SDN controller was not involved in
various aspects of service provisioning and viability. The second
example will come all these aspects in more detail.
<------------------ L3 service-1 ------------------->
<------------------ TE-Tunnel-1 ------------------>
<----------------- IP link-1 ----------------->
<------------- L0 service-1 ------------->
|----------| |------------------|
| Coherent | | |
| Pluggable| <--> | SDN Controller |
| Manifest | | |
|----------| |------------------|
^
|
v
|------------------|
port_a | |
|------| p1 |------| |
| R1 ++-\ | m1 | | port_b
|------| \ |------| |------| p2 |------|
\ | | m3 |-----++ R2 |
\ |------| |------| |------|
\-| m2 | |
|------| |
| |
|------------------|
Legend:
---- Optical fibers
++ p1,p2 Coherent pluggables
R1, R2 Packet device (i.e., Router)
m1, m2, m3 Photonic node (ROADM)
Figure 16: Coherent Pluggable Manifest Usage 1
In this example, all optical and IP/MPLS services had been already
provisioned and deployed and the packet over optical network is fully
functional.
Rokui, et al. Expires 22 April 2025 [Page 40]
Internet-Draft Modelling Optical Pluggables October 2024
Within packet devices R1 and R2, coherent pluggables p1 and p2, are
installed, interfacing through ports port_a and port_b, respectively.
Both coherent pluggables are provisioned for the following
operational-mode.
* [organization-id, operational-mode] = [OIF, 0x3E]
A single photonic service is established between these pluggables and
an IP link is mapped to this L0 photonic service. The overlay TE-
Tunnel-1 and L3 service-1 had been also provisioned. The following
steps outline the details of how this network is discovered and
managed by SDN controllers (note that the SDN controller was not
involved in provisioning):
* Packet devices (R1, R2), pluggables (p1, p2), and photonic devices
(m1, m2, m3) are all discovered by SDN controllers.
* The SDN controller also discovers all underlay and overlay
services, i.e., L0 service-1, IP link-1, TE-Tunnel-1 and L3
servcie-1.
* The SDN controller has the network inventory, including coherent
pluggables p1 and p2. In particular for coherent pluggables,
basic information such as pluggable type, vendor, manufacturer,
serial number and software version will be provided by pluggables
to SDN controller.
* The inventory of packet devices R1 and R2 contains the
configurations of pluggable attributes such as "configured
operational-mode," "configured central frequency," and "configured
output power".
* Specifically, using the basic information of pluggables p1 and p2
such as pluggable type, vendor, manufacturer, serial number and
software version collected earlier from packet devices R1 and R2,
the SDN controller can use the "Coherent Pluggable Manifest," to
access the entire information of both pluggables p1 and p2. This
includes all supported operational-modes along with all attributes
related to each supported operational-mode.
* The SDN controller can collect all PM telemetry data from the
network (including pluggables).
* The SDN controller can collect all alarm notifications from the
network (including pluggables).
* The SDN controller can further change, modify, optimize the
network (if needed).
Rokui, et al. Expires 22 April 2025 [Page 41]
Internet-Draft Modelling Optical Pluggables October 2024
11.2. Example-2: Coherent Pluggables Manifest
The example in Figure 17 demonstrates the usage of the "Coherent
Pluggable Manifest" for entire lifecycle of photonic service from
including service planning, viability, provisioning, collection of PM
telemetry, collection of alarm notifications and optimization.
Note that the packet over optical network in Figure 17 is not created
yet. The ports port_a and port_b of packet device R1 and R2 are
empty and can accept coherent pluggables. In addition, ports port_a
and port_b are not connected to the optical network yet, i.e., there
is no connection between packet devices R1, R2 and optical network.
The port_a and port_b of packet device R1 and R2 can be potentially
connected to any photonic nodes m1, m2 or m3.
Operator's goal is to use the SDN controller to plan, provision and
monitor an optimal IP link-2 between packet devices R1 and R2.
Optionally they can also provision overlay TE-Tunnel-2 and L3
service-2. To achieve this, the SDN controller should first plan an
optical service-2, perform the viability to make sure this photonic
service is feasible, provision it and then map it to an IP link-2.
Rokui, et al. Expires 22 April 2025 [Page 42]
Internet-Draft Modelling Optical Pluggables October 2024
<------------------ L3 service-2 ------------------->
<------------------ TE-Tunnel-2 ------------------>
<----------------- IP link-2 ----------------->
<------------- L0 service-2 ------------->
|----------| |------------------|
| Coherent | | |
| Pluggable| <--> | SDN Controller |
| Manifest | | |
|----------| |------------------|
^
|
v
|------------------|
port_a | |
|------| |------| |
| R1 .........| m1 | | port_b
|------| . |------| |------| |------|
. | | m3 |....... R2 |
. |------| |------| |------|
..| m2 | |
|------| |
| |
|------------------|
Legend:
..... Packet device can be potentially
connected to photonic nodes m1, m2, m3
R1, R2: Packet device (i.e., Router)
m1, m2, m3 Photonic node (ROADM)
port_a Router R1 port which is empty and can
potentially populated by coherent pluggables
port_b Router R2 port which is empty and can
potentially populated by coherent pluggables
Figure 17: Coherent Pluggable Manifest Usage 2
Let's assume that the operator of this network has already purchased
coherent pluggables from Vendor-X, which can support the following
two operational-modes. Note that the detail information of these
operational-modes including all optical and photonic attributes are
already uploaded to "Coherent Pluggable Manifest" by Vendor-X and
OIF.
* [organization-id, operational-mode] = [OIF, 0x3E]
* [organization-id, operational-mode] = [Vendor-X, 0x22]
Rokui, et al. Expires 22 April 2025 [Page 43]
Internet-Draft Modelling Optical Pluggables October 2024
The following steps outline the details of how this network is
planned, provisioned, discovered and managed by SDN controllers:
* At first, there are no coherent pluggables installed in the packet
devices yet. There are also no connection between packet devices
and optical network.
* All packet devices (R1, R2) and photonic devices (m1, m2, m3) are
managed by the SDN controller.
* As a result, the SDN controller maintains an inventory of packet
and photonic devices within the network (i.e., nodes R1, R2, m1,
m2, m3).
* To create the IP link-2, the SDN controller should plan and then
provision the optical service-2 between port_a and port_b.
* To this end, the SDN controller should first design an optical
service and then performs the viability check to make sure the
optical service is viable in this network.
* So, the SDN controller calculates the best optical path from
port_a to port_b.
* Next, the SDN controller performs the viability on optical route
to make sure the optical path is viable in the network.
* To do viability, the SDN controller checks all attributes of all
operational-modes to find the most optimal operational-mode. To
do this, the SDN controller connects to the "Coherent Pluggable
Manifest" and access all optical and photonic attributes of all
operational-modes (such as chromatic dispersion, FEC, modulation,
polarization mode dispersion etc.) and performs the viability.
* After performing the optical path calculation and optical
viability, the SDN controller selects the best coherent pluggable
to be installed on port_a and port_b and the best optical route
from port_a to port_b.
* Upon completion of the photonic viability check, the SDN
controller determines which photonic devices (m1, m2, m3) should
be connected to ports port_a and port_b.
* The SDN controller informs the operator of the selected coherent
pluggables for ports port_a and port_b and provides instructions
on how to connect them to the respective photonic devices (m1, m2,
m3).
Rokui, et al. Expires 22 April 2025 [Page 44]
Internet-Draft Modelling Optical Pluggables October 2024
* The operator installs the designated pluggables into ports port_a
and port_b and connects them to the specified photonic devices.
* The SDN controller then manages the newly installed pluggables.
* As part of the photonic viability process, the SDN controller
knows the specific attributes of the pluggables, including
"configured operational mode," "configured central frequency," and
"configured output power."
* As a result, the SDN controller configures these configurations to
each pluggable on port_a and port_b
* The SDN controller should also configure optical nodes m1, m2, m3
with attributes such as output power.
* The SDN controller provisions the optical service_1 between two
conheret pluggables on port_a and port_b.
* The SDN controller also provisions the IP link-2 between packet
device R1 and R2.
* The SDN controller can collect all PM telemetry data from the
network (including pluggables).
* The SDN controller can collect all alarm notifications from the
network (including pluggables).
* The SDN controller can further change, modify, optimize the
network (if needed).
12. Security Considerations
TODO Security
13. IANA Considerations
This document has no IANA actions.
14. References
14.1. Normative References
[G.698.2] "Amplified multichannel dense wavelength division
multiplexing applications with single channel optical
interfaces", November 2018, .
Rokui, et al. Expires 22 April 2025 [Page 45]
Internet-Draft Modelling Optical Pluggables October 2024
[Impairment]
"A YANG Data Model for Optical Impairment-aware Topology",
4 March 2024, .
[OIF-400ZR]
"Implementation Agreement 400ZR", November 2022,
.
[OIF-CMIS] "OIF Implementation Agreement (IA) Common Management
Interface Specification (CMIS))", OIF CMIS IA , September
2024, .
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC2119, March 1997,
.
[RFC8174] Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174,
May 2017, .
[SFF8024] "SFF Module Management Reference Code Tables", November
2023, .
14.2. Informative References
[ietf-impairment-yang]
"A YANG Data Model for Optical Impairment-aware Topology",
6 January 2025, .
[ietf-layer0-yang]
"Common YANG Data Types for Layer 0 Networks", 26 January
2025, .
[ietf-optical-interface-yang]
"A YANG model to manage the optical interface parameters
for an external transponder in a WDM network", 6 January
2025, .
Rokui, et al. Expires 22 April 2025 [Page 46]
Internet-Draft Modelling Optical Pluggables October 2024
[RFC8453] Ceccarelli, D., Ed. and Y. Lee, Ed., "Framework for
Abstraction and Control of TE Networks (ACTN)", RFC 8453,
DOI 10.17487/RFC8453, August 2018,
.
Acknowledgments
TODO acknowledge.
Contributors
Nigel Davis
Ciena
Email: ndavis@ciena.com
Italo Busi
Huawei Technologies
Email: italo.busi@huawei.com
Sergio Belotti
Nokia
Email: sergio.belotti@nokia.com
Dieter Beller
Nokia
Email: dieter.beller@nokia.com
Roberto Manzotti
Cisco
Email: rmanzott@cisco.com
Prasenjit Manna
Cisco
Email: prmanna@cisco.com
Gabriele Galimberti
Individual
Email: ggalimbe56@gmail.com
Harish Venkatraman
Infinera
Rokui, et al. Expires 22 April 2025 [Page 47]
Internet-Draft Modelling Optical Pluggables October 2024
Email: hvenkatraman@infinera.com
Gyan Mishra
Verizon
Email: gyan.s.mishra@verizon.com
Stefan Melin
Telia
Email: stefan.melin@teliacompany.com
Majid Hossein Poor
Telstra
Email: majid.hosseinpoor@team.telstra.com
Dacian Demeter
Telus
Email: dacian.demeter@telus.com
Authors' Addresses
Reza Rokui
Ciena
Email: rrokui@ciena.com
Aihua Guo
Futurewei Technologies
Email: aihuaguo.ietf@gmail.com
Phil Bedard
Cisco
Email: phbedard@cisco.com
B Swamynathan
Nokia
Email: swamynathan.b@nokia.com
Gert Grammel
Juniper
Email: ggrammel@juniper.net
Rokui, et al. Expires 22 April 2025 [Page 48]